Skip to Content

Technical Specification: Structured Cabling System (Copper and Fibre)

This specification covers a complete structured cabling system: Category 6/6A horizontal copper, optical fibre backbone, racks, bonding, labelling and certification testing. It is written for consultants, engineers and contractors to insert into tender documents with light editing.

Vendor-neutral, no brand names. Review it against the code adopted for your project and fill in the values in [brackets].

PART 1 — GENERAL

1.1 Scope of Work

The Contractor shall supply, install, terminate, label, test, certify and document a complete Structured Cabling System (SCS) for [project name], comprising horizontal copper cabling, optical fibre backbone cabling, telecommunications rooms and racks, pathway coordination, bonding and administration, as shown on the drawings and described in this section. The scope includes:

  • Horizontal balanced twisted-pair cabling of Category [6 / 6A] from each telecommunications outlet to the floor or zone telecommunications room (TR), quantity [number of outlets].
  • Optical fibre backbone cabling between the main equipment room (ER) and each TR, and between buildings where shown, using [OS2 single-mode / OM4 multimode / both].
  • Copper backbone cabling for voice or legacy services where shown, [number of pairs] per TR.
  • Racks, cabinets, patch panels, fibre distribution panels, cable managers, patch cords and power distribution units (PDUs).
  • Coordination of cable containment (cable tray, conduit, trunking) with the electrical contractor and installation of all containment inside TRs and ERs.
  • Telecommunications bonding and earthing infrastructure inside TRs and ERs.
  • Labelling and administration records, permanent link and channel certification testing, fibre testing, as-built documentation and the manufacturer system warranty.

Active network equipment (switches, routers, wireless access points) is specified in a separate section and is excluded from this section unless stated otherwise.

1.2 Related Sections and Systems

  • Active Network (LAN switching and Wi-Fi).
  • IP video surveillance, access control, IP telephony, public address and building management systems that use the SCS as transport.
  • Electrical works: power to racks, earthing system, cable tray and conduit installed by the electrical contractor.
  • Fire stopping of penetrations, and HVAC for TRs and ERs.

1.3 Reference Standards

The installation shall comply with the latest editions of the following standards. Where requirements differ, the more stringent shall apply.

  • ANSI/TIA-568.0-D — Generic Telecommunications Cabling for Customer Premises.
  • ANSI/TIA-568.1-D — Commercial Building Telecommunications Infrastructure Standard.
  • ANSI/TIA-568.2-D — Balanced Twisted-Pair Telecommunications Cabling and Components Standard.
  • ANSI/TIA-568.3-D — Optical Fiber Cabling and Components Standard.
  • ANSI/TIA-569-E — Telecommunications Pathways and Spaces.
  • ANSI/TIA-606-C — Administration Standard for Telecommunications Infrastructure.
  • ANSI/TIA-607-D — Generic Telecommunications Bonding and Grounding (Earthing) for Customer Premises.
  • ISO/IEC 11801-1 — Information technology — Generic cabling for customer premises — Part 1: General requirements.
  • ISO/IEC 14763-2 — Implementation and operation of customer premises cabling — Planning and installation.
  • ISO/IEC 14763-3 — Implementation and operation of customer premises cabling — Testing of optical fibre cabling.
  • IEC 61935-1 — Specification for the testing of balanced and coaxial information technology cabling — Installed cabling.
  • IEC 60603-7 series — Connectors for electronic equipment (8-way modular connectors).
  • ITU-T G.652.D and ITU-T G.657.A1 — Characteristics of single-mode optical fibre and cable.
  • IEC 61280-4-1 and IEC 61280-4-2 — Fibre optic installed cable plant attenuation measurement (multimode and single-mode).
  • IEC 60332-1-2, IEC 60332-3 series, IEC 61034-2 and IEC 60754-1/-2 — Flame propagation, smoke density and halogen acid gas tests for LSZH cables.
  • The Egyptian electrical installation code and the Egyptian fire protection code, as applicable.

1.4 Definitions

  • Permanent link: the installed horizontal cable from the patch panel to the outlet, maximum 90 m, excluding patch cords.
  • Channel: the end-to-end transmission path including the permanent link and equipment and work-area cords, maximum 100 m.
  • TR / ER: telecommunications room / equipment room.
  • ODF: optical distribution frame or rack-mounted fibre distribution panel.
  • LSZH: low smoke zero halogen cable sheath.
  • OLTS / OTDR: optical loss test set / optical time-domain reflectometer.

1.5 Submittals

  • Manufacturer datasheets for every component, showing the performance category, materials and fire rating.
  • Third-party component and channel verification certificates for the offered Category [6 / 6A] system.
  • Shop drawings: outlet layout per floor, TR and ER layouts, rack elevations, backbone riser diagram, containment routes and labelling scheme.
  • Fibre loss budget calculation for every backbone link at the operating wavelengths.
  • Rack power and heat load schedule, and cable tray fill calculations for main routes.
  • Samples on request: cable, outlet, patch panel module, faceplate and label.
  • Test equipment list with valid calibration certificates (not older than 12 months).
  • Installer certification from the system manufacturer.
  • As-built drawings, test reports and warranty certificate at handover.

1.6 Quality Assurance

  • All copper components (cable, connectors, panels, cords) shall be from a single manufacturer or a manufacturer-approved combination, so that the complete channel is covered by one system warranty.
  • The Contractor shall be a certified installer of the offered system, with at least [3] completed projects of similar size in the last [5] years, and shall employ at least [2] technicians holding current manufacturer installation certificates.
  • The manufacturer shall operate an ISO 9001 certified quality management system.
  • Local technical support and stock of standard components shall be available in Egypt.

1.7 Delivery, Storage and Handling

  • Deliver materials in original sealed packaging with manufacturer labels and batch numbers.
  • Store cable reels and fibre drums in a dry, covered area, protected from direct sun, dust and mechanical damage, within the temperature range stated by the manufacturer.
  • Do not install cabling until the area is enclosed, dry and free of construction dust and heavy works.

1.8 Warranty

  • The Contractor shall warrant workmanship for [2] years from the date of provisional acceptance.
  • The manufacturer shall issue a system performance and application warranty of not less than [20] years, covering all passive components and the transmission performance of every link to the category specified, registered in the name of the Employer.
  • Defective components or failed links during the warranty shall be repaired or replaced and re-tested at no cost to the Employer.

1.9 Spare Parts

  • Provide spare quantities of not less than [2%] of installed outlets, jacks and patch cords of each length and colour, and [1] spare fibre panel adaptor plate per type.

PART 2 — PRODUCTS

2.1 System Description

The SCS shall follow a hierarchical star topology: main cross-connect in the ER, horizontal cross-connects in TRs, and telecommunications outlets in work areas. Each TR shall serve outlets within a horizontal cable length of 90 m. The entire copper system shall be of one performance category throughout, [Category 6A for new buildings and Wi-Fi 6/7 access points / Category 6 elsewhere]. Backbone links shall be optical fibre, with a minimum of [12] fibre cores per TR.

2.2 Horizontal Copper Cable

  • 4-pair, 100 Ω balanced twisted-pair cable, Category [6 / 6A], compliant with ANSI/TIA-568.2-D and ISO/IEC 11801-1 (Class E / Class EA).
  • Construction: [U/UTP / F/UTP], conductors 23 AWG or 22 AWG solid bare copper. Copper-clad aluminium or copper-clad steel conductors are not acceptable.
  • Characterised to 250 MHz for Category 6 and 500 MHz for Category 6A.
  • Sheath: [LSZH] tested to IEC 60332-1-2, IEC 61034-2 and IEC 60754-1/-2 in occupied buildings and escape routes; [IEC 60332-3 category] where bundled runs are required by the fire strategy.
  • Outside diameter shall be compatible with the offered connectors and tray fill design.
  • Printed sheath markings at 1 m intervals showing category, construction and length.
  • Support of IEEE 802.3bt Type 4 PoE with acceptable temperature rise in bundles shall be declared by the manufacturer.
  • Colour: [blue for data / other per Employer standard].

2.3 Telecommunications Outlets and Faceplates

  • RJ45 modular jacks to IEC 60603-7 series, same category and manufacturer as the cable, T568[B] wiring.
  • Tool-less or punch-down termination with insulation displacement contacts rated for not less than 750 mating cycles.
  • Shielded jacks for F/UTP systems with 360° shield termination.
  • Faceplates: [single / dual] port, [86 × 86 mm] British-style or as required by the back box, with angled or flat shuttered ports and label windows.
  • Floor boxes, desk modules and ceiling outlets for access points and cameras as shown on drawings.
  • Each work area shall have not less than [2] outlets unless noted otherwise.

2.4 Copper Patch Panels

  • 19-inch, 1U, 24-port or 48-port [modular / fixed] panels of the same category and manufacturer as the cable.
  • Rear cable support bar and port identification on the front.
  • Shielded panels with an earthing terminal for F/UTP systems.
  • Panel capacity shall include [20%] spare ports.

2.5 Patch Cords

  • Factory-made and factory-tested stranded copper cords of the same category and manufacturer, with boots preventing snagging. Field-made cords are not acceptable.
  • LSZH sheath. Lengths [0.5 / 1 / 2 / 3 m] for racks and [3 m] for work areas.
  • Quantity: one cord in the rack and one in the work area per active outlet, colours per the colour code agreed with the Employer.

2.6 Racks and Cabinets

  • ER racks: 19-inch floor-standing, [42U], [800 mm wide × 1000 mm deep], static load not less than [600 kg].
  • TR racks: [42U, 800 × 800 mm] floor-standing or [12U–18U, 600 × 600 mm] wall-mounted, as shown.
  • Perforated front and rear doors (not less than 60% open area) with locks, removable side panels, cable entry at top and bottom with brush seals, adjustable levelling feet and earthing points on all metal parts.
  • Vertical cable managers on both sides of each floor-standing rack, and a 1U horizontal manager for every patch panel or switch.
  • Two PDUs per rack, 220–240 V AC 50 Hz, [16 A], not less than [8] outlets each, fed from separate circuits where available.
  • Roof-mounted fan tray with thermostat where the heat load requires it; blanking panels for empty spaces.

2.7 Backbone Optical Fibre Cable

  • Single-mode: OS2, ITU-T G.652.D, or G.657.A1 where tight bends are required.
  • Multimode: OM4 (OM3 only where specifically allowed), 50/125 µm, laser-optimised.
  • Indoor cables: tight-buffered or semi-tight, LSZH sheath. Inter-building and underground cables: loose tube, gel-free or dry water blocking, [corrugated steel tape / non-metallic] armour, UV and rodent resistant, PE outer sheath.
  • Core count: [12] cores per TR (minimum), [24] cores for inter-building links, including not less than [50%] spare cores.
  • Maximum cable attenuation per ANSI/TIA-568.3-D: multimode 3.0 dB/km at 850 nm and 1.5 dB/km at 1300 nm (cabled values per manufacturer, not worse than the standard); single-mode 1.0 dB/km inside plant and 0.5 dB/km outside plant at 1310/1550 nm.

2.8 Fibre Distribution Panels (ODF) and Connectivity

  • Rack-mounted 1U/2U sliding drawer panels with splice trays, bend radius control, front and rear cable management and earthing for armoured cables.
  • Termination by fusion splicing of factory pigtails. Field-polished connectors are not acceptable.
  • Connectors: [LC duplex] (default) or [SC], to IEC 61754 series. Single-mode connectors UPC (APC only where required by the application, e.g. video overlay or PON).
  • Maximum insertion loss per mated connector pair 0.75 dB and per fusion splice 0.3 dB (ANSI/TIA-568.3-D); typical values offered shall be stated.
  • Adapter colours: single-mode UPC blue, APC green, multimode OM3/OM4 aqua or heather violet.
  • Fibre patch cords: factory-terminated, duplex, LSZH, matching fibre type and connectors, [1 / 2 / 3 m].

2.9 Copper Backbone (where required)

  • Category 3 or better multi-pair cable, [25 / 50 / 100] pairs, LSZH, terminated on rack-mounted voice panels or IDC blocks.

2.10 Containment Within TRs and ERs

  • Overhead ladder or basket tray above racks, sized for 50% initial fill, earthed and bonded.
  • Fibre runners or separate trays for optical cables where the quantity justifies it.
  • Main building containment (by others) shall be coordinated with the SCS drawings and shall meet ANSI/TIA-569-E, with conduit fill not exceeding [40%] and bend radii suitable for Category 6A and fibre cables.

2.11 Bonding and Earthing Components

  • Primary bonding busbar (PBB) in the ER and secondary bonding busbar (SBB) in each TR, tin-plated copper, pre-drilled, on insulated stand-offs, per ANSI/TIA-607-D.
  • Telecommunications bonding backbone (TBB) and bonding conductors: insulated copper, minimum 6 AWG (16 mm²), sized per ANSI/TIA-607-D for the length.
  • Rack bonding kits, two-hole compression lugs, paint-piercing washers and jumpers for doors and side panels.

2.12 Labels

  • Machine-printed, durable labels with smudge-resistant print; wrap-around self-laminating labels for cables. Handwritten labels are not acceptable.

PART 3 — EXECUTION

3.1 Examination

  • Inspect pathways, back boxes, TRs and ERs before installation. Confirm that containment is complete, burr-free, earthed and of correct size, and that rooms are clean, lockable, ventilated and powered.
  • Report in writing any condition that prevents compliance with this specification. Starting installation means acceptance of conditions.

3.2 Installation

  • Install cabling per ANSI/TIA-568.1-D, ANSI/TIA-569-E, ISO/IEC 14763-2 and the manufacturer's instructions.
  • Permanent link length shall not exceed 90 m; channel length shall not exceed 100 m.
  • Pulling tension on 4-pair cables shall not exceed 110 N. Bend radius shall not be less than 4 times the cable diameter for installed U/UTP and 8 times for F/UTP, and as specified by the manufacturer for fibre (generally 10 times diameter installed, 20 times during pulling).
  • Do not kink, crush or over-tighten cables. Use hook-and-loop ties inside racks and trays; nylon ties, if allowed outside racks, shall be hand-tight only.
  • Maintain separation from power cables, fluorescent fittings, motors and transformers per ISO/IEC 14763-2 / ANSI/TIA-569-E, and not less than [300 mm] from unscreened power cables where no metallic divider is installed. Cross power cables at 90°.
  • Bundle sizes for PoE cabling shall follow the manufacturer's guidance to limit temperature rise.
  • Leave a service loop of [3 m] in the TR and [0.3 m] at the outlet. Do not leave loops inside walls in a tight coil.
  • Untwist pairs not more than 13 mm at terminations; maintain the shield continuity on F/UTP systems.
  • Fibre cables shall be run in innerduct or dedicated containment where shared with copper, with a [5 m] slack in each TR stored on the ODF or a slack bracket.
  • Seal all penetrations through fire-rated walls and floors with approved fire-stopping systems restoring the original rating.
  • Bond racks, trays, ODFs with armoured cables and shielded panels to the SBB/PBB. Connect the PBB to the building main earthing terminal. Earth resistance of the building earthing system shall be [≤ 5 Ω] or as set by the electrical design. Measured DC resistance between any rack and the SBB shall not exceed [0.1 Ω].

3.3 Cabling Administration and Labelling

  • Apply an identification scheme per ANSI/TIA-606-C, agreed with the Employer before installation.
  • Typical format: [building-floor-TR-rack-panel-port], e.g. B1-02-TR1-R01-A-24, identical on both ends, on the faceplate, patch panel port and cable jacket within 300 mm of each termination.
  • Label racks, panels, ODFs, fibre cables (both ends and at pull boxes), bonding conductors and busbars.
  • Deliver records in electronic form (spreadsheet) linking each outlet to its room, panel port and test result.

3.4 Configuration of Cross-Connects

  • Arrange panels to separate cabling types and services logically, with switches interleaved or adjacent to minimise cord lengths, as approved in rack elevations.
  • Dress patch cords neatly through horizontal and vertical managers; cords shall not block equipment airflow or door closing.

3.5 Testing and Commissioning

Copper testing

  • Test 100% of installed links as permanent links per ANSI/TIA-568.2-D / ISO/IEC 11801-1 using a certified field tester with accuracy Level IIIe (Category 6A) or Level III (Category 6) to IEC 61935-1, with current firmware, test limits and calibration.
  • Parameters: wire map, length, propagation delay, delay skew, insertion loss, NEXT, PSNEXT, ACR-F, PSACR-F, return loss, DC loop resistance and DC resistance unbalance; and alien crosstalk sampling for Category 6A where specified by the Engineer.
  • Shield continuity shall be tested for F/UTP links.
  • Any result marked as marginal pass ("*" PASS) shall be investigated and reported; the Engineer may require re-termination.
  • Channel testing of [5%] of links, selected by the Engineer, with the actual patch cords installed.

Fibre testing

  • Tier 1: bidirectional loss testing of every fibre with an OLTS per ANSI/TIA-568.3-D and ISO/IEC 14763-3, one-reference-jumper method, at 850/1300 nm (multimode, with encircled-flux compliant launch) and 1310/1550 nm (single-mode).
  • Measured loss shall not exceed the calculated loss budget (fibre length × attenuation + connector pairs × 0.75 dB + splices × 0.3 dB).
  • Tier 2: OTDR traces of every fibre from both ends, with launch and receive cords, showing length, event loss and reflectance, for [backbone and inter-building links].
  • Inspect and clean every connector end face with a video inspection probe before testing and before connecting active equipment.

Acceptance

  • Provisional acceptance requires: 100% of links passing, labels matching records, racks dressed, bonding verified, test results in native tester format and PDF, and the manufacturer warranty registration submitted.
  • The Engineer may witness re-testing of up to [10%] of links; if more than [2%] of witnessed links fail, the Contractor shall re-test all links at its own cost.

3.6 Training

  • Provide [1] day of training for the Employer's IT staff on system layout, labelling scheme, moves/adds/changes, fibre handling and cleaning, and warranty procedures.

3.7 Documentation and Handover

  • As-built drawings (PDF and CAD) showing outlet locations with identifiers, cable routes, rack elevations, riser and fibre diagrams.
  • Complete test results in native format and PDF, with a summary sheet per TR.
  • Administration records, equipment datasheets, calibration certificates and the manufacturer warranty certificate.

Related tools and products

Frequently asked questions

When should Category 6A be chosen instead of Category 6?

Category 6A is chosen when 10 Gb/s over 100 m is needed, for Wi-Fi 6/7 access points and high-power IEEE 802.3bt PoE loads, and in new buildings expected to serve for many years. Category 6 is adequate for typical offices, cameras and 1 Gb/s access points.

What is the difference between a permanent link and a channel test?

The permanent link is the installed cable from the patch panel to the outlet, up to 90 m, and is tested for every link. The channel adds the patch cords at both ends, up to 100 m, and is normally tested on a sample selected by the Engineer.

Why does the specification require solid bare copper conductors?

Copper-clad aluminium conductors do not comply with TIA and ISO standards; their higher resistance causes heating under PoE loads, failures in certification tests and loss of the warranty.

Is OLTS testing alone enough for fibre?

OLTS (Tier 1) testing is mandatory on every fibre to measure total loss against the loss budget. OTDR (Tier 2) testing is added for backbone and inter-building links to locate splices, connectors and any fault along the cable.

Need help designing your project?

Do Link engineers help you choose equipment and work out quantities, and they design and execute CCTV, network, intercom and access control projects, with wholesale and project prices for contractors, technicians, companies and finishing companies.