PoE Budget Calculator
Add the PoE devices and their quantities to see the total power, the PoE standard each device needs, and the switch ports and power budget that fit.
| Device | Qty | Max power (W) |
|---|
Safe switch PoE budget (the larger of the two figures below)
- Total device power0 W
- By consumption + cable loss + 25% margin0 W
- If the switch reserves power by class0 W
- PoE ports needed0
- Highest standard needed-
- Suggested switch-
If the switch datasheet says it allocates power by actual consumption, the first figure is enough. Also make sure each port supports the standard of the device on it, and keep cable runs within 100 m.
PoE standards
| Standard | Common name | At the switch | At the device |
|---|---|---|---|
| IEEE 802.3af | PoE | 15.4 W | 12.95 W |
| IEEE 802.3at | PoE+ | 30 W | 25.5 W |
| IEEE 802.3bt Type 3 | PoE++ | 60 W | 51 W |
| IEEE 802.3bt Type 4 | PoE++ | 90 W | 71.3 W |
The difference between power at the switch and power at the device is the most a 100 m cable can lose. The calculator therefore compares each device's draw with the power available at the device to pick the standard it needs, and adds cable loss in proportion to cable length.
How the switch counts power
Some switches allocate power by what each device actually draws; others reserve the full class power on each port: 15.4 W for any PoE device and 30 W for any PoE+ device, even if the camera draws only 5 W. The calculator therefore shows two figures and suggests the larger one, unless the switch datasheet says it allocates by actual consumption.
How to choose the switch
- Port count: one PoE port per device, plus one or more ports to the recorder or router, ideally with spare ports.
- PoE budget: the total power the switch shares across all ports; it must cover all devices with margin.
- Standard per port: some switches offer PoE+ or PoE++ on certain ports only, so check the datasheet.
- Port speed: 100 Mbps ports are enough for most cameras, while modern access points need gigabit ports.
Worked example
Twelve fixed cameras at 5 W each and two access points at 15 W each, with 50 m average cable: 90 W of consumption, about 137 W with cable loss and a 25% margin. A switch that reserves by class would reserve 15.4 W per camera and 30 W per access point, about 245 W. A 16-port PoE switch with at least a 245 W budget fits, or 140 W if it allocates by actual consumption, and the two access points need PoE+ ports.
Related products from Do Link
Frequently asked questions
What is the difference between 802.3af, 802.3at and 802.3bt?
802.3af (PoE) gives up to 15.4 W at the switch and 12.95 W at the device; 802.3at (PoE+) up to 30 W and 25.5 W; 802.3bt (PoE++) up to 60 W and 51 W for Type 3, and up to 90 W and 71.3 W for Type 4.
How many watts does an IP camera use?
Fixed 2 to 4MP cameras usually draw a few watts at most, more with night illumination on, while PTZ cameras need much more. Always use the maximum power consumption from the camera datasheet.
Is it enough that the total is below the switch budget?
Two conditions apply: the total must not exceed the switch total PoE budget, and each port must support the standard and power of the device on it. A switch with a large budget may not offer PoE+ on every port.
What does it mean that a switch reserves power by class?
Some switches reserve the maximum power of the device class on each port, such as 15.4 W for a PoE device and 30 W for a PoE+ device, whatever it actually draws. The switch budget then runs out faster, so the calculator shows this figure and suggests the larger one.
What is the maximum cable length with PoE?
The standard allows 100 m for the channel including patch cords; about 90 m of fixed cable is the common rule. Pure copper cable is better for long runs because CCA loses more power.
Why does the calculator add a 25% margin?
So the switch does not run at its limit, to cover higher draw at night when illumination turns on, and to leave room for devices added later.
Need help designing your project?
Do Link engineers help you choose equipment and work out quantities, and they design and execute CCTV, network, intercom and access control projects, with wholesale and project prices for contractors, technicians, companies and finishing companies.